It's best to draw it by drawing too much, it hurts too much
5 thoughts on “What are XFG1 and XSC1 in the simulation software? Where is in Multisim10?”
Mabel
In the simulation software, XFG1 is a functional signal generator, SXC1 is an oscilloscope, which can be found in the instrument panel. If the instrument is horizontal, from left to right, the second is XFG1, and the fourth and fifth are XSC1. The functional signal generator is a signal -occurring device that can generate some specific periodic time function waveforms (sine waves, square waves, triangular waves, sawtooth waves, pulse waves, etc.). To tens of MMH. In addition to communication, instrument and automatic control system testing, function signal generators are also widely used in other non -electrical measurement areas. The oscilloscope is mainly used to display the waveform of the measured signal, and it can also be used to measure the frequency and cycle of the measured signal. In the middle, the instrument bar has a two -track oscilloscope and a four -channel oscilloscope. Double -click the corresponding icon to open the parameter setting interface. Its parameter settings are basically the same as the actual oscilloscope. The expansion information: Id the function signal generator with the same voltage level as the electronic device. Hold the working component of the electrical appliance (electrical header), contact the electrode head of the generator to the electrode head of the test device, and then press the "work" switch. At this time, the sound and light signal from electrical appliances indicates that the performance of electrical appliances is intact. It without sound and lighting indicator static electricity measures, repairs or replacement should be repaired before use. When testing the near -current alarm helmet, you only need to close the electrode head of the high -voltage signal generator to the alarm and press the "work" switch. The note: 1, function signal generator with "power indicator". If the indicator light is not on during use, the battery should be replaced before use. 2. When not in use, the function signal generator should be placed in a dry and ventilated place to avoid moisture. Reference information Source: signal generator-Baidu 100 Keke
In the simulation software, XFG1 is a functional signal generator and SXC1 is an oscilloscope. They can be found in the instrument panel. If the instrument is horizontal, from left to right, the second is XFG1, and the fourth and fifth are XSC1. M functional signal generator is a signal -occurring device that can generate certain periodic time function waveforms (sine waves, square waves, triangular waves, sawtooth waves, pulse waves, etc.). Weikh to tens of MMB. In addition to the testing of communication, instrument, and automatic control systems, it is also widely used in other non -electrical measurement areas. The oscilloscope is mainly used to display the waveform of the measured signal, and it can also be used to measure the frequency and cycle of the measured signal. In the middle, the instrument bar has a dual -track oscilloscope and a four -channel oscilloscope. Double -click the corresponding icon to open the parameter settings interface. Its parameter settings are basically the same as the parameter settings of the actual oscilloscope. The expansion data The use of functional signal generators and precautions Ip using In the same voltage signal generator of the same voltage as electrical appliances. The handheld electrical appliance work part (electrical header) contacts the electrode head of the generator's electrical electrical electrical electrical electrical electrical header and press the "work" switch. If the silent light indication indicates that the electrical appliances are faulty, it should be repaired or replaced after use. When detecting near -electric alarm helmets, you only need to close the electrode head of the high -voltage signal generator close to the alarm to press the "work" switch. If Note 1, the signal generator has "power indicator". When used, the indicator light is not high, and the battery should be replaced before using it. 2, the signal generator should be placed in a dry and ventilated place to avoid moisture. Reference information Source: signal generator -Baidu Encyclopedia
In the simulation software, XFG1 is a function signal generator, and XSC1 is an indicator. You can find it in the meter bar. If the instrument bar is horizontal, the number from left to right, the second is XFG1, and the fourth and fifth are XSC1. The function signal generator is used to provide a voltage source of sine waves, triangular waves, and square wave signals. The virtual icon corresponding to the instrument packet immediately opens the virtual function signal generator parameter settings control panel, which can be set as required. n quemakes are mainly used to display the waveform of the measured signal, and can also measure parameters such as the frequency and cycle of the measured signal. There are dual -traces and four -channel oscilloscopes in the instrument bar, and double -click the corresponding icon, that is, open the parameter setting interface. Its parameter settings are basically the same as the setting of the real oscilloscope. Extension information:
1. Classification of oscilloscope: different categories according to structure and performance ① ordinary oscilloscope. The circuit structure is simple, the frequency band is narrow, and the scanning linearity is poor. It is only used to observe the waveform. ② Multiple oscilloscope. The frequency band is wide, the scanning linearity is good, and can be quantitatively tested on DC, low -frequency, high -frequency, ultra -high -frequency signals and pulse signals. With the amplitude caliber and time caliber, the accuracy of the measurement can reach ± 5%. ③ multi -line oscilloscope. The multi -beam display wave tube can display the waveforms of the same frequency signals on the fluorescent screen at the same time. There is no time difference and the timing relationship is accurate. ④ multi -traces of oscilloscope. With the structure of electronic switches and door control circuits, the waveforms of the same frequency signals can be displayed on the fluorescent screen of a single beam tube. But there is a time difference, and the timing relationship is inaccurate. ⑤ Sample oscilloscope. The sampling technology is used to convert the high -frequency signal into an analog low -frequency signal for display, and the effective frequency band can reach GHz level. ⑥ Memory oscilloscope. The storage wave tube or digital storage technology is adopted, and the transient, non -periodic phenomenon, and ultra -low -frequency signal of a single electrical signal are retained on the fluorescent screen of the display wave tube or stored in the circuit for repeated testing. hu Digital oscilloscope. There is a microprocessor inside and a digital display outside. Some products can display waveforms and characters on the fluorescent screen of the display wave tube. The measured signal signal Soloter (A/D converter) is sent to the data memory. Through the keyboard operation, the data of the captured waveform parameters can be added, subtracted, multiplied, divided, and found the average value. , Find the calculations of the square root value, the average root value, etc., and show the number of answers. Reference information Source: "Circuit Design and Application" Wang Guanhua edited the virtual instrument of the National Defense Industry Press 3.2 Section of functional signal generator, 3.4 and 3.5 dual -tracting oscilloscopes and four -channel oscilloscope
In the simulation software, XFG1 is a functional signal generator, SXC1 is an oscilloscope, which can be found in the instrument panel. If the instrument is horizontal, from left to right, the second is XFG1, and the fourth and fifth are XSC1. The functional signal generator is a signal -occurring device that can generate some specific periodic time function waveforms (sine waves, square waves, triangular waves, sawtooth waves, pulse waves, etc.). To tens of MMH. In addition to communication, instrument and automatic control system testing, function signal generators are also widely used in other non -electrical measurement areas. rnrnrn示波器主要用于显示被测信号的波形，也可以用来测量被测信号的频率和周期。 In the middle, the instrument bar has a two -track oscilloscope and a four -channel oscilloscope. Double -click the corresponding icon to open the parameter setting interface. Its parameter settings are basically the same as the actual oscilloscope. The expansion information: Id the function signal generator with the same voltage level as the electronic device. Hold the working component of the electrical appliance (electrical header), contact the electrode head of the generator to the electrode head of the test device, and then press the "work" switch. At this time, the sound and light signal from electrical appliances indicates that the performance of electrical appliances is intact.
It without sound and light indicator static electricity meter, it should be repaired or replaced before use. When testing the near -current alarm helmet, you only need to close the electrode head of the high -voltage signal generator to the alarm and press the "work" switch. The note: 1, function signal generator with "power indicator". If the indicator light is not on during use, the battery should be replaced before use.
2. When not in use, the function signal generator should be placed in a dry and ventilated place to avoid moisture
In the simulation software, XFG1 is a functional signal generator, SXC1 is an oscilloscope, which can be found in the instrument panel. If the instrument is horizontal, from left to right, the second is XFG1, and the fourth and fifth are XSC1.
The functional signal generator is a signal -occurring device that can generate some specific periodic time function waveforms (sine waves, square waves, triangular waves, sawtooth waves, pulse waves, etc.). To tens of MMH. In addition to communication, instrument and automatic control system testing, function signal generators are also widely used in other non -electrical measurement areas.
The oscilloscope is mainly used to display the waveform of the measured signal, and it can also be used to measure the frequency and cycle of the measured signal. In the middle, the instrument bar has a two -track oscilloscope and a four -channel oscilloscope. Double -click the corresponding icon to open the parameter setting interface. Its parameter settings are basically the same as the actual oscilloscope.
The expansion information:
Id the function signal generator with the same voltage level as the electronic device. Hold the working component of the electrical appliance (electrical header), contact the electrode head of the generator to the electrode head of the test device, and then press the "work" switch. At this time, the sound and light signal from electrical appliances indicates that the performance of electrical appliances is intact.
It without sound and lighting indicator static electricity measures, repairs or replacement should be repaired before use. When testing the near -current alarm helmet, you only need to close the electrode head of the high -voltage signal generator to the alarm and press the "work" switch.
The note:
1, function signal generator with "power indicator". If the indicator light is not on during use, the battery should be replaced before use.
2. When not in use, the function signal generator should be placed in a dry and ventilated place to avoid moisture.
Reference information Source:
signal generator-Baidu 100 Keke
In the simulation software, XFG1 is a functional signal generator and SXC1 is an oscilloscope. They can be found in the instrument panel. If the instrument is horizontal, from left to right, the second is XFG1, and the fourth and fifth are XSC1.
M functional signal generator is a signal -occurring device that can generate certain periodic time function waveforms (sine waves, square waves, triangular waves, sawtooth waves, pulse waves, etc.). Weikh to tens of MMB. In addition to the testing of communication, instrument, and automatic control systems, it is also widely used in other non -electrical measurement areas.
The oscilloscope is mainly used to display the waveform of the measured signal, and it can also be used to measure the frequency and cycle of the measured signal. In the middle, the instrument bar has a dual -track oscilloscope and a four -channel oscilloscope. Double -click the corresponding icon to open the parameter settings interface. Its parameter settings are basically the same as the parameter settings of the actual oscilloscope.
The expansion data
The use of functional signal generators and precautions
Ip using
In the same voltage signal generator of the same voltage as electrical appliances. The handheld electrical appliance work part (electrical header) contacts the electrode head of the generator's electrical electrical electrical electrical electrical electrical header and press the "work" switch.
If the silent light indication indicates that the electrical appliances are faulty, it should be repaired or replaced after use. When detecting near -electric alarm helmets, you only need to close the electrode head of the high -voltage signal generator close to the alarm to press the "work" switch.
If Note
1, the signal generator has "power indicator". When used, the indicator light is not high, and the battery should be replaced before using it.
2, the signal generator should be placed in a dry and ventilated place to avoid moisture.
Reference information Source: signal generator -Baidu Encyclopedia
In the simulation software, XFG1 is a function signal generator, and XSC1 is an indicator. You can find it in the meter bar. If the instrument bar is horizontal, the number from left to right, the second is XFG1, and the fourth and fifth are XSC1.
The function signal generator is used to provide a voltage source of sine waves, triangular waves, and square wave signals. The virtual icon corresponding to the instrument packet immediately opens the virtual function signal generator parameter settings control panel, which can be set as required.
n quemakes are mainly used to display the waveform of the measured signal, and can also measure parameters such as the frequency and cycle of the measured signal. There are dual -traces and four -channel oscilloscopes in the instrument bar, and double -click the corresponding icon, that is, open the parameter setting interface. Its parameter settings are basically the same as the setting of the real oscilloscope.
Extension information:
1. Classification of oscilloscope: different categories according to structure and performance
① ordinary oscilloscope. The circuit structure is simple, the frequency band is narrow, and the scanning linearity is poor. It is only used to observe the waveform.
② Multiple oscilloscope. The frequency band is wide, the scanning linearity is good, and can be quantitatively tested on DC, low -frequency, high -frequency, ultra -high -frequency signals and pulse signals. With the amplitude caliber and time caliber, the accuracy of the measurement can reach ± 5%.
③ multi -line oscilloscope. The multi -beam display wave tube can display the waveforms of the same frequency signals on the fluorescent screen at the same time. There is no time difference and the timing relationship is accurate.
④ multi -traces of oscilloscope. With the structure of electronic switches and door control circuits, the waveforms of the same frequency signals can be displayed on the fluorescent screen of a single beam tube. But there is a time difference, and the timing relationship is inaccurate.
⑤ Sample oscilloscope. The sampling technology is used to convert the high -frequency signal into an analog low -frequency signal for display, and the effective frequency band can reach GHz level.
⑥ Memory oscilloscope. The storage wave tube or digital storage technology is adopted, and the transient, non -periodic phenomenon, and ultra -low -frequency signal of a single electrical signal are retained on the fluorescent screen of the display wave tube or stored in the circuit for repeated testing.
hu Digital oscilloscope. There is a microprocessor inside and a digital display outside. Some products can display waveforms and characters on the fluorescent screen of the display wave tube.
The measured signal signal Soloter (A/D converter) is sent to the data memory. Through the keyboard operation, the data of the captured waveform parameters can be added, subtracted, multiplied, divided, and found the average value. , Find the calculations of the square root value, the average root value, etc., and show the number of answers.
Reference information Source: "Circuit Design and Application" Wang Guanhua edited the virtual instrument of the National Defense Industry Press 3.2 Section of functional signal generator, 3.4 and 3.5 dual -tracting oscilloscopes and four -channel oscilloscope
Reference materials Source: Baidu Encyclopedia-oscilloscope
In the simulation software, XFG1 is a functional signal generator, SXC1 is an oscilloscope, which can be found in the instrument panel. If the instrument is horizontal, from left to right, the second is XFG1, and the fourth and fifth are XSC1.
The functional signal generator is a signal -occurring device that can generate some specific periodic time function waveforms (sine waves, square waves, triangular waves, sawtooth waves, pulse waves, etc.). To tens of MMH. In addition to communication, instrument and automatic control system testing, function signal generators are also widely used in other non -electrical measurement areas. rnrnrn示波器主要用于显示被测信号的波形，也可以用来测量被测信号的频率和周期。 In the middle, the instrument bar has a two -track oscilloscope and a four -channel oscilloscope. Double -click the corresponding icon to open the parameter setting interface. Its parameter settings are basically the same as the actual oscilloscope.
The expansion information:
Id the function signal generator with the same voltage level as the electronic device. Hold the working component of the electrical appliance (electrical header), contact the electrode head of the generator to the electrode head of the test device, and then press the "work" switch. At this time, the sound and light signal from electrical appliances indicates that the performance of electrical appliances is intact.
It without sound and light indicator static electricity meter, it should be repaired or replaced before use. When testing the near -current alarm helmet, you only need to close the electrode head of the high -voltage signal generator to the alarm and press the "work" switch.
The note:
1, function signal generator with "power indicator". If the indicator light is not on during use, the battery should be replaced before use.
2. When not in use, the function signal generator should be placed in a dry and ventilated place to avoid moisture
The interface is on the far right, a vertical column. Seeing it, XFG1 is the second, the function generator, XFC1 is the fourth,